|
Valore Glass
and Tile Water Repellant and Cleaner
Never squeegee or get water dots again on your shower
glass or mirrors! Hard water is water that has
high mineral content (in contrast with soft water).
Hard water is generally not harmful to one's health, but
can pose serious problems in your shower area. Hard
water will leave dots all over you glass and tile.
Valore if use ounce a week will prevent hard water spots
and soap scum with no scrubbing or no need to squeegee.
Oh, Yes We Did, invent a cleaner and repellant to save
you time and money.
DIRECTIONS
-
Area must be clean and free of oils and
dirt. Minerals left on glass may
cause some streaking.
-
If your shower has a lot of bar soap and
hard water deposits, purchase our Water
Dot Remover. For heavy build up
some scrubbing will have to take place.
When the Valore is used on soiled glass
or mirror, streaks may occur because it
will release all impurities.
-
Always do a small test area before
spraying the whole shower down.
-
Spray Valore on all the shower walls and
glass enclosure. For mirror
application, just spray on and wipe
down, you will not have to get all
Valore off the glass as it will dry
streak free. Wiping the glass will
remove finger prints and soil.
-
On the inside of the shower spray down
glass and tile, covering area very good,
after your shower at least once a week.
If finger prints are present just
lightly wipe with cloth.
-
Let dry as it will dry spot free with no
water dots.
-
Spray shower down once a week and the
shower will dry in about 15 minutes.
-
The water from the shower will do all
the cleaning for you.
No need to squeegee the glass or tile at all.
There will be no water dots on your glass after your
done taking a shower and the water evaporates. We
are eliminating the time spent to keep your shower
looking brand new for years.
Valore can
be used on:
1.
Sealed Natural
Stone Tile but should not be used on unsealed polish
stone.
2.
All Glass (shower, mirrors, windows and
automotive).
3.
Escutcheons covers and all hardware around your glass
enclosure.
4.
Metal, Cast iron, and Cast aluminum
5. Culture
Marble
6.
Tile, Grout,
and Cement
7. Always
do a test area first!
$13.99 per bottle
$39.95 for 4 bottles
Water
Dots Present on Your Glass?
Benaz Water Dot Remover will remover all water dots. Always perform a small test area in a inconspicuous spot before
spraying the whole area down.
 1. Always perform a test area first on
the surface.
2. Use a microfiber cloth and
apply some of the paste on the cloth.
3. Rub onto the glass or ceramic
tile in a circular motion.
4. This will remove all of the
first stage water dots. Heavily etched glass we need several
applications.
5. Rinse the paste off of the
surface with water and use a clean cloth to wipe as you rinse.
6. Clean the glass off with
Valore.
7. Spray Valore on the glass again
and rinse off the Valore with water.
8. Do not use on surfaces that can
be harmed by the use of a mild abrasive or don't use on any acid
sensitive surfaces such as polished marble etc.
9. Always
wear gloves and safety goggles.
$13.99 per bottle
$39.95 for 4 bottles
CLEAN UP
Use water and a clean sponge to clean up any spills.
Small spills can be cleaned up with paper towels or a
dry towel.
EMERGENCY
WARNING: May
be a skin irritant to person with
sensitive skin. Such person should use
gloves and wash hands after use. This
material is an eye irritant. If
accidental entry to eye occurs, please
flush with cold water and contact your
physician. Read M.S.D.S before using any
chemical products in your facility and
follow OSHA safe standards and house
hygiene practices.
WARRANTY
|
